MAX6978AUE+【PDF 7/13 页】IC LED DVR CONST-CURR 16TSSOP

您好，
买卖IC网欢迎您。
请登录
免费注册

3页 4页 5页 6页 [7页]8页 9页 10页 11页

8-Port, 5.5V Constant-Current LED Driver with

LED Fault Detection and Watchdog

Detailed Description

The MAX6978 LED driver comprises a 4-wire serial

interface driving eight constant-current sinking open-

drain output ports. The outputs drive LEDs in either sta-

tic or multiplex applications (Figure 1). The constant-

current outputs are guaranteed for current accuracy

not only with chip-supply voltage variations (5V ±10%

and 3V to 5.5V), but also over a realistic range of driver

output voltage drop (0.5V to 2.5V). The drivers use cur-

rent-sensing feedback circuitry (not simple current mir-

rors) to ensure very small current variations over the full

allowed range of output voltage (see the Typical

Operating Characteristics ).

The 4-wire serial interface comprises an 8-bit shift reg-

ister and an 8-bit transparent latch. The shift register is

written through a clock input CLK and a data input DIN

and the data propagates to a data output DOUT. The

data output allows multiple drivers to be cascaded and

operated together. The contents of the 8-bit shift regis-

ter are loaded into the transparent latch through a

latch-enable input LE. The latch is transparent to the

shift register outputs when high, and latches the current

state on the falling edge of LE.

Each driver output is an open-drain constant-current

sink that should be connected to the cathode of either

a single LED or a series string of multiple LEDs. The

LED anode can be connected to a supply voltage of up

to 5.5V, independent of the MAX6978 supply, V+. The

constant-current capability is up to 55mA per output,

set for all eight outputs by an external resistor, R SET .

Initial Power-Up and Operation

An internal reset circuit clears the internal registers of

the MAX6978 on power-up. All outputs OUT0 – OUT7,

therefore, initialize high impedance, and the interface

output DOUT initializes low, regardless of the initial

logic levels of the CLK, DIN, OE , and LE inputs.

4-Wire Serial Interface

The serial interface on the MAX6978 is a 4-wire serial

interface using four inputs (DIN, CLK, LE, OE ) and a

data output (DOUT). This interface is used to write dis-

play data to the MAX6978. The serial-interface data

word length is 8 bits, D0 – D7.

The functions of the five interface pins are as follows.

DIN is the serial-data input, and must be stable when it

is sampled on the rising edge of CLK. Data is shifted in,

MSB first. This means that data bit D7 is clocked in first,

followed by 7 more data bits, finishing with the LSB D0.

CLK is the serial-clock input, which shifts data at DIN

into the MAX6978 8-bit shift register on its rising edge.

LE is the latch load input of the MAX6978, which trans-

fers data from the MAX6978 8-bit shift register to its 8-bit

latch when LE is a high (transparent latch), and latches

the data on the LE falling edge of LE (Figure 2). The ris-

ing edge of LE loads fault data into the MAX6978 8-bit

shift register, replacing bits D6 and D5 with fault data.

This fault data is automatically shifted out through DOUT

when the next display data is shifted in.

The fourth input provides output-enable control of the

output drivers. OE is high to force outputs OUT0 – OUT7

high impedance, without altering the contents of the

output latches, and low to enable outputs OUT0 – OUT7

to follow the state of the output latches.

Table 1. 4-Wire Serial-Interface Truth Table

SERIAL CLOCK

DATA INPUT

SHIFT-REGISTER

CONTENTS

LOAD

INPUT

LATCH CONTENTS

BLANKING

INPUT

OUTPUT CONTENTS

INPUT

DIN

CLK

D 0

D 1

D 2

… D n-1 D n

LE

D 0

D 1

D 2

… D n-1 D n

OE

D 0

D 1

D 2

… D n-1 D n

H

L

X

H

L

R 0

R 1

R 1

R 1

R 2

R 2

R 2

… R n-2 R n-1

… R n-2 R n-1

… R n-1 R n

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

X

X

X

…

X

X

H

R 0

R 1

R 2

— R n-1 R n

—

—

—

—

—

—

—

—

—

P 1

P 2

P 3

… P n-1 P n

L

P 0

P 1

P 2

… P n-1 P n

L

P 0

P 1

P 2

… P n - 1 P n

—

—

—

—

—

—

—

—

—

X

X

X

…

X

X

H

Hi-Z Hi-Z Hi-Z … Hi-Z Hi-Z

L = Low-logic level

H = High-logic level

X = Don’t care

P = Present state

R = Previous state

_______________________________________________________________________________________

7

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

MAX6979AUG+ IC LED DRIVER LINEAR 24-TSSOP

MAX6983AUG+T IC LED DRIVER LINEAR 24-TSSOP

MAX71020AEUI+ IC ENERGY METER 1PH 28TSSOP

MAX7302ATE+ IC LED DRIVER LINEAR 16-TQFN

MAX7307AUB+T IC LED DRIVER LINEAR 10-UMAX

MAX831EVKIT-SO EVAL KIT FOR MAX831

MAX8513EVKIT EVAL KIT FOR MAX8513

MAX8552EUB+ IC DRIVER MOSFET HS 10-UMAX

相关代理商/技术参数

MAX6978AUE+T 功能描述:LED照明驱动器 8-Port, 5.5V CC LED Driver w/Fault Det RoHS:否制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N

MAX6978AUE-T 功能描述:LED照明驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N

MAX6979ANG 功能描述:LED显示驱动器 RoHS:否制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube

MAX6979APG 制造商:Maxim Integrated Products 功能描述:- Rail/Tube

MAX6979AUG 功能描述:LED显示驱动器 RoHS:否制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube

MAX6979AUG+ 功能描述:LED照明驱动器 16Port 5.5V Constant Current LED Driver RoHS:否制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N

MAX6979AUG+T 功能描述:LED照明驱动器 16Port 5.5V Constant Current LED Driver RoHS:否制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N

MAX6979AUG-T 功能描述:LED显示驱动器 RoHS:否制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube